Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Here in the next paragraph you can get a good deal of excellent ideas in relation to How to Install a Bathtub.
Setting up a bathtub isn't exactly brain surgery, however it does require solid plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is conveniently available, the task can relocate easily; if you have to open a wall to eliminate the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's skills, although you will require an assistant to vacate the old tub as well as set in the brand-new one. Ensure you have certified on your own for the task as well as fit attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly assist you set up a new bath tub in your restroom if you have actually already acquired a brand-new bathtub as well as don't require to change the plan of your previous water supply pipes.
Your devices as well as product list should consist of the following:
Getting ready for the Installment
To start with, the supporting framework supplied with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps unit to avoid strain on the tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its final setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is separate the water system. After doing so, activate the taps to drain pipes any water staying in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will come from the pipelines. Once the supply pipes have actually been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the bath tub in the called for setting. The wood boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bathtub till the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water and also check all joints and brand-new pipework for leaks as well as tighten them if required. Fill up the bath tub and also inspect the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been made use of at the very least when as this will settle it right into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making certain that the washing machines remain in area in between the faucet as well as the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The former type must be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a stiff seal, causing the water to pass through the wall between the bath and the tiling, causing complications with dampness as well as feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill up the tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture rather very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily available on the marketplace. It is advisable to fit the floor tiles using water-resistant or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very serious about How to Install a Bathtub Yourself and I hope you enjoyed the blog entry. Sharing is nice. You just don't know, you may just be helping someone out. Thanks a lot for your time. Please check up our website back soon.
Excellence awaits, dial! Report this page